Notifications
Clear all
| Posts with their shortened content | ||
 |
RE: Router Sled Conversion to CNC Router Sled
By [email protected], 3 weeks ago
Forum
General Discussion
|
|
| Thanks all for the help. Opened my eyes!At this point, I'm looking at Corgi ESP32 6 Axis CNC Controller for FluidNC SKU CQA231222CE3 Any experience out there with this?Any chance DIYCNC could supply i... | ||
 |
RE: Router Sled Conversion to CNC Router Sled
By 1900, 3 weeks ago
Forum
General Discussion
|
|
| If I’d had other options when I bought the 4-axis CNC controller, I wouldn’t have chosen this one. It doesn’t support firmware upgrades, and there’s no dedicated 0–10V output for controlling an AC spi... | ||
 |
RE: More choices on the air cooled spindle?
By Frank, 3 weeks ago
Forum
Product Questions
|
|
| Hi, The manufacturer gave us the full list, and yes, they do have a 2.2 kW model in this series. However, we think that for spindles above 1.5 kW, water cooling is worth considering. We're concerned t... | ||
 |
More choices on the air cooled spindle?
By michel02, 3 weeks ago
Forum
Product Questions
|
|
| Hi, I am looking this: Is there Higher Wattage spindle, 1.5kw is small I think. Thanks | ||
 |
RE: Router Sled Conversion to CNC Router Sled
By T Zhao, 3 weeks ago
Forum
General Discussion
|
|
| Please refer user manual: $45 to configure 2nd Y, or A | ||
 |
RE: Router Sled Conversion to CNC Router Sled
By Andy78, 3 weeks ago
Forum
General Discussion
|
|
| Good to know, how to configure this? | ||
|
|
RE: Router Sled Conversion to CNC Router Sled
By T Zhao, 3 weeks ago
Forum
General Discussion
|
|
| The MKS DLC32 Max board, can use two Y axis seperately: Use A axis as 2nd Y. In this case, A axis is gone. So X YY Z, or XYZA | ||
|
|
RE: Router Sled Conversion to CNC Router Sled
By Frank, 3 weeks ago
Forum
General Discussion
|
|
| As far as I know, even the 4 Axis board has two Y drivers, they are still in parallel connection. Both those two boards. Based on the link above, grbl1.1H needs more limited switch, I couldn't find th... | ||
|
|
RE: Router Sled Conversion to CNC Router Sled
By Frank, 3 weeks ago
Forum
General Discussion
|
|
| The question is actually if the Y1 and Y2 are using seperate drivers, or share a single driver. Here is an useful information: | ||
|
|
RE: Router Sled Conversion to CNC Router Sled
By Andy78, 3 weeks ago
Forum
General Discussion
|
|
| Too plastic, but expensive... 😊 haven't use it... | ||
|
|
RE: Router Sled Conversion to CNC Router Sled
By T Zhao, 3 weeks ago
Forum
General Discussion
|
|
| Hi Andy, would you mind to share your experience with our handwheel? | ||
|
|
RE: Router Sled Conversion to CNC Router Sled
By Andy78, 3 weeks ago
Forum
General Discussion
|
|
| I’m using the MKS CNC board to drive my CL motors: . So far, I’m happy with this board. I also received the CNC handwheel last week, but I haven’t tested it yet. I’m not familiar with the 4-axis GRBL ... | ||
|
|
RE: 3D Printer Filament Bundle Sale
By Frank, 3 weeks ago
Forum
General Discussion
|
|
| If the color you specified is in the same catelog of our color options, yes, you can add to the list, we can try to get that for you. Thanks | ||
|
|
RE: 3D Printer Filament Bundle Sale
By Andy78, 3 weeks ago
Forum
General Discussion
|
|
| Hi, if I found a color from eSun store, but in your list, may I add it to the excel sheet? Thanks, Andy | ||
|
|
Router Sled Conversion to CNC Router Sled
By [email protected], 3 weeks ago
Forum
General Discussion
|
|
| Is the Nema 23 Closed Loop Stepper Motor Bundle - LC57H276 + LCDA257 compatible with the 4 Axis GRBL CNC Control Board - Board without Driver ? Does the control board support Y1 and Y2 homing and squa... | ||