Notifications
Clear all
Jun 17, 2026 10:35 pm
I am using this topic to discuss Voron 2.4 Parts and Kit
Parts list:
| Category | Description | Qty | DIY Notes |
|---|---|---|---|
| Fasteners | M5x40 SHCS | 22 | |
| M5x30 BHCS | 22 | ||
| M5x16 BHCS | 35 | ||
| M5x10 BHCS | 35 | ||
| M5 Hexnut | 16 | ||
| M5 Post-install T-nut | 68 | ||
| M5 1mm Shim | 42 | ||
| M4x6 BHCS | 7 | ||
| M4 Knurled Nut (DIN 466-B) | 4 | ||
| M3x50 SHCS | 2 | ||
| M3x40 SHCS | 30 | ||
| M3x30 SHCS | 25 | ||
| M3x25 SHCS | 6 | ||
| M3x20 SHCS | 22 | ||
| M3x16 SHCS | 20 | ||
| M3x12 SHCS | 41 | ||
| M3x10 FHCS | 4 | ||
| M3x6 FHCS | 8 | ||
| M3x8 SHCS | 187 | ||
| M3x6 BHCS | 11 | ||
| M3 Hexnut | 6 | ||
| M3 Post-install T-nut | 103 | ||
| M3 Hammer Head T-nuts | 60 | ||
| M3 Washer | 4 | ||
| M3 Threaded Insert (M3x5x4) | 110 | ||
| M2x10 Self-tapping Screw | 18 | ||
| Motion | GT2 80T Pulley (5mm ID 6mm W) | 4 |
Motion Parts Kit:: https://diycnc.ca/product/voron-2-4-full-set-motion-parts-kit/ |
| GT2 20T Pulley (5mm ID 6mm W) | 3 | ||
| GT2 20T Pulley (5mm ID 9mm W) | 4 | ||
| GT2 16T Pulley (5mm ID 6mm W) | 4 | ||
| GT2 20T Toothed Idler (5mm ID 6mm W) | 2 | ||
| GT2 20T Toothed Idler (5mm ID 9mm W) | 4 | ||
| F695 Bearing | 20 | ||
| 625 Bearing | 12 | ||
| Ø 5x60mm Shaft, D Cut | 4 | ||
| Ø 5x35mm Shaft (trim to size) | 1 | ||
| GT2 Belt Loop (6mm W) - 188mm | 4 | ||
| GT2 Open Belt LL-2GT-9 (9mm wide) - 1200mm | 4 | ||
| BMG Extruder Components Kit | 1 | ||
| Linear Rail MGN9H 400mm | 6 | Refer: https://diycnc.ca/product/voron-2-4-linear-rail-kit/ | |
| Linear Rail MGN12H 400mm | 1 | ||
| GT2 Open Belt LL-2GT-6 (6mm wide) - 2000mm | 2 | ||
| Electronics | Omron D2F-01L Micro Switch | 3 | |
| Inductive Probe (See sourcing guide) | 1 | ||
| Hotend Kit (24V) | 1 | ||
| 50x50x15 Centrifugal Fan (24V) | 1 | ||
| 40x40x10 Axial Fan (24V) | 1 | ||
| Mini 12864 Display | 1 | ||
| ZF Rocker Switch DPST 16A ON-OFF | 1 | ||
| TycoElectronics 10EGG1-1 Filtered Power Inlet (NA/UK) | 1 | ||
| TycoElectronics 10EGG1-2 Filtered Power Inlet (EU) | 1 | ||
| Medium Blow Fuse 5x20mm 4A (220V mains) | 2 | ||
| Medium Blow Fuse 5x20mm 8A (120v mains) | 1 | ||
| Keystone CAT6 Insert (Optional) | 1 | ||
| 60x60x20 Fan (24V) | 3 | ||
| Controller with 7+ Stepper outputs | 1 | ||
| TMC2209 Stepper Motor Driver | 7 | ||
| USB Cable for selected controller | 1 | ||
| RaspberryPi 3B+ or better | 1 | ||
| Mean Well LRS-200-24 PSU | 1 | ||
| Mean Well RS-25-5 PSU | 1 | ||
| Omron G3A-210B-DC5 SSR | 1 | ||
| DIN Rail Mount Bracket for G3A SSR | 1 | ||
| BAT85 Diode | 1 | ||
| C13 Power Cord | 1 | ||
| Thermal Fuse (150C) | 1 | ||
| NEMA17 Motor 17HS19-2004S | 6 | ||
| NEMA14 Motor 36STH20-1004AHG | 1 | ||
| Vibration Management | Rubber Foot (1.5x.75", 38x19mm) | 4 | |
| Frame | OpenBuilds Billet Angle Corner Connector (2020) | 4 | Refer Frame Kit: https://diycnc.ca/product/3d-printer-framing-diy-kit-for-voron-2-4/ |
| Misumi HFSB5-2020-340 | 1 | ||
| DIN 3 Rails (35mm W) - 465mm | 2 | ||
| Misumi HFSB5-2020-430 | 1 | ||
| Misumi HFSB5-2020-450 | 2 | ||
| Misumi HFSB5-2020-470-TPW | 10 | ||
| Misumi HFSB5-2020-530-LCP-RCP | 4 | ||
| Misc | Fume Extractor Carbon Filter Element | 1 | |
| 4mm Threaded Bowden Coupler | 1 | ||
| 3M VHB Tape 5952 | 1 | ||
| Loctite Blue Threadlocker Stick | 1 | ||
| Mobil EP1/2 Grease | 1 | ||
| Single Sided Foam Tape 1mm Thick (5m) | 1 | ||
| Single Sided Foam Tape 3mm Thick (5m) | 1 | ||
| Ø6x3mm Neodimium Magnet | 8 | ||
| PTFE Tube (4mm OD 3mm ID) - 1000mm | 1 | ||
| PTFE Tube (4mm OD 2mm ID) - 300mm | 1 | ||
| Cables | Nylon Cable Ties Small (.07-.10", 1.8-2.7mm wide) | 42 | |
| 18AWG Wire (10ft/3m total) | 1 | ||
| 20AWG High-flex Wire (10ft/3m total) | 1 | ||
| 22-24AWG High-flex Wire (min 19 strand)(250ft/76m total) | 1 | ||
| Female Spade Crimp Terminal (18-22AWG, .250", 6.35mm) | 7 | ||
| Fork Spade Crimp Terminal (18-22AWG,#10) | 5 | ||
| Ring Crimp Terminal (16-22AWG, #6) | 1 | ||
| JST XH Connector, 3 Position Male/Female Pair plus Pins | 1 | ||
| Connector kit matching your controller choice (usually JST-XH) | 1 | ||
| Crimp Ferrule Kit (covering sizes 24AWG to 18AWG) | 1 | ||
| MicroFit3 Connector Plug 4 Position | 4 | ||
| MicroFit3 Connector Plug 3 Position | 1 | ||
| MicroFit3 Connector Plug 2 Position | 2 | ||
| MicroFit3 Connector Receptacle 4 Position | 4 | ||
| MicroFit3 Connector Receptacle 3 Position | 1 | ||
| MicroFit3 Connector Receptacle 2 Position | 2 | ||
| MLX Power Receptacle 3 Position (bed wiring) | 1 | ||
| MLX Power Plug 3 Position | 1 | ||
| MLX Male Pin | 6 | ||
| MLX Female Pin | 6 | ||
| MicroFit3 Female Pin | 40 | ||
| MicroFit3 Male Pin | 40 | ||
| WAGO 221-415 Lever-Nuts | 3 | ||
| 10x10 Generic Cable Chain (405mm) | 2 | ||
| 10x15 Generic Cable Chain (545mm) | 1 | ||
| Panels | Coroplast Sheet - 469x469x4 mm | 2 | |
| Coroplast Sheet - 483x503x4 mm | 1 | ||
| Acrylic Sheet Clear - 241.5x503x3 mm | 2 | ||
| Acrylic Sheet Clear - 483x503x3 mm | 2 | ||
| Acrylic Sheet Clear - 483x483x3 mm | 1 | ||
| Buildplate | MIC6 5/16" Plate - 14"x14" | 1 | |
| Adhesive Magnetic Sheet - 14"x14" | 1 | ||
| Spring Steel Flexible Print Surface - 14"x14" | 1 | ||
| Keenovo Silicone AC Heater w/ thermistor - 300x300mm (650W) | 1 |
1 Reply
Jun 18, 2026 6:12 am
We are using Bambu ABS or ASA filament and follow the printing parameters: 0.2mm Layer, 4~5 wall, 40~50% infill
The color choices (with Bambu Lab Filament Color Code):
- ABS Black (40101)
- ABS Red (40200)
- ABS Blue (40600)
- ABS Solver (40102)
- ABS Orange (40300)
- ABS Bambu Green (40500)
-------------------------------------------------------
- ASA Black (45101)
- ASA Gray (45102)
- ASA Green (45500)
- ASA Blue (45600)
- ASA Red (45200)