DIY Projects - DIY CNC 3D Printer Robot Forum https://diycnc.ca/community/diy-projects/ DIYCNC Customer Support & Tech Sharing for Canadian DIY Hobbyists and Makers. en-US Fri, 23 Oct 2026 20:13:36 +0000 wpForo 60 Voron 2.4 Parts and Kit https://diycnc.ca/community/diy-projects/voron-2-4-parts-and-kit/ Thu, 18 Jun 2026 03:35:07 +0000 I am using this topic to discuss Voron 2.4 Parts and Kit

Parts list:

Category Description Qty DIY Notes
Fasteners M5x40 SHCS 22  
  M5x30 BHCS 22  
  M5x16 BHCS 35  
  M5x10 BHCS 35  
  M5 Hexnut 16  
  M5 Post-install T-nut 68  
  M5 1mm Shim 42  
  M4x6 BHCS 7  
  M4 Knurled Nut (DIN 466-B) 4  
  M3x50 SHCS 2  
  M3x40 SHCS 30  
  M3x30 SHCS 25  
  M3x25 SHCS 6  
  M3x20 SHCS 22  
  M3x16 SHCS 20  
  M3x12 SHCS 41  
  M3x10 FHCS 4  
  M3x6 FHCS 8  
  M3x8 SHCS 187  
  M3x6 BHCS 11  
  M3 Hexnut 6  
  M3 Post-install T-nut 103  
  M3 Hammer Head T-nuts 60  
  M3 Washer 4  
  M3 Threaded Insert (M3x5x4) 110  
  M2x10 Self-tapping Screw 18  
Motion GT2 80T Pulley (5mm ID 6mm W) 4

Motion Parts Kit::

https://diycnc.ca/product/voron-2-4-full-set-motion-parts-kit/
  GT2 20T Pulley (5mm ID 6mm W) 3  
  GT2 20T Pulley (5mm ID 9mm W) 4  
  GT2 16T Pulley (5mm ID 6mm W) 4  
  GT2 20T Toothed Idler (5mm ID 6mm W) 2  
  GT2 20T Toothed Idler (5mm ID 9mm W) 4  
  F695 Bearing 20  
  625 Bearing 12  
  Ø 5x60mm Shaft,  D Cut 4  
  Ø 5x35mm Shaft (trim to size) 1  
  GT2 Belt Loop (6mm W) - 188mm 4  
  GT2 Open Belt LL-2GT-9 (9mm wide) - 1200mm 4  
  BMG Extruder Components Kit 1  
  Linear Rail MGN9H 400mm 6 Refer:  https://diycnc.ca/product/voron-2-4-linear-rail-kit/
  Linear Rail MGN12H 400mm 1  
  GT2 Open Belt LL-2GT-6 (6mm wide) - 2000mm 2  
Electronics Omron D2F-01L Micro Switch 3  
  Inductive Probe (See sourcing guide) 1  
  Hotend Kit (24V) 1  
  50x50x15 Centrifugal Fan (24V) 1  
  40x40x10 Axial Fan (24V) 1  
  Mini 12864 Display 1  
  ZF Rocker Switch DPST 16A ON-OFF 1  
  TycoElectronics 10EGG1-1 Filtered Power Inlet (NA/UK) 1  
  TycoElectronics 10EGG1-2 Filtered Power Inlet (EU) 1  
  Medium Blow Fuse 5x20mm 4A (220V mains) 2  
  Medium Blow Fuse 5x20mm 8A (120v mains) 1  
  Keystone CAT6 Insert (Optional) 1  
  60x60x20 Fan (24V) 3  
  Controller with 7+ Stepper outputs 1  
  TMC2209 Stepper Motor Driver 7  
  USB Cable for selected controller 1  
  RaspberryPi 3B+ or better 1  
  Mean Well LRS-200-24 PSU 1  
  Mean Well RS-25-5 PSU 1  
  Omron G3A-210B-DC5 SSR 1  
  DIN Rail Mount Bracket for G3A SSR 1  
  BAT85 Diode 1  
  C13 Power Cord 1  
  Thermal Fuse (150C) 1  
  NEMA17 Motor 17HS19-2004S 6  
  NEMA14 Motor 36STH20-1004AHG 1  
Vibration Management Rubber Foot (1.5x.75", 38x19mm) 4  
Frame OpenBuilds Billet Angle Corner Connector (2020) 4 Refer Frame Kit: https://diycnc.ca/product/3d-printer-framing-diy-kit-for-voron-2-4/
  Misumi HFSB5-2020-340 1  
  DIN 3 Rails (35mm W) - 465mm 2  
  Misumi HFSB5-2020-430 1  
  Misumi HFSB5-2020-450 2  
  Misumi HFSB5-2020-470-TPW 10  
  Misumi HFSB5-2020-530-LCP-RCP 4  
Misc Fume Extractor Carbon Filter Element 1  
  4mm Threaded Bowden Coupler 1  
  3M VHB Tape 5952 1  
  Loctite Blue Threadlocker Stick 1  
  Mobil EP1/2 Grease 1  
  Single Sided Foam Tape 1mm Thick (5m) 1  
  Single Sided Foam Tape 3mm Thick (5m) 1  
  Ø6x3mm Neodimium Magnet 8  
  PTFE Tube (4mm OD 3mm ID) - 1000mm 1  
  PTFE Tube (4mm OD 2mm ID) - 300mm 1  
Cables Nylon Cable Ties  Small (.07-.10",  1.8-2.7mm wide) 42  
  18AWG Wire (10ft/3m total) 1  
  20AWG High-flex Wire (10ft/3m total) 1  
  22-24AWG High-flex Wire (min 19 strand)(250ft/76m total) 1  
  Female Spade Crimp Terminal (18-22AWG, .250", 6.35mm) 7  
  Fork Spade Crimp Terminal (18-22AWG,#10) 5  
  Ring Crimp Terminal (16-22AWG, #6) 1  
  JST XH Connector,  3 Position Male/Female Pair plus Pins 1  
  Connector kit matching your controller choice (usually JST-XH) 1  
  Crimp Ferrule Kit (covering sizes 24AWG to 18AWG) 1  
  MicroFit3 Connector Plug 4 Position 4  
  MicroFit3 Connector Plug 3 Position 1  
  MicroFit3 Connector Plug 2 Position 2  
  MicroFit3 Connector Receptacle 4 Position 4  
  MicroFit3 Connector Receptacle 3 Position 1  
  MicroFit3 Connector Receptacle 2 Position 2  
  MLX Power Receptacle 3 Position (bed wiring) 1  
  MLX Power Plug 3 Position 1  
  MLX Male Pin 6  
  MLX Female Pin 6  
  MicroFit3 Female Pin 40  
  MicroFit3 Male Pin 40  
  WAGO 221-415 Lever-Nuts 3  
  10x10 Generic Cable Chain (405mm) 2  
  10x15 Generic Cable Chain (545mm) 1  
Panels Coroplast Sheet - 469x469x4 mm 2  
  Coroplast Sheet - 483x503x4 mm 1  
  Acrylic Sheet Clear - 241.5x503x3 mm 2  
  Acrylic Sheet Clear - 483x503x3 mm 2  
  Acrylic Sheet Clear - 483x483x3 mm 1  
Buildplate MIC6 5/16" Plate - 14"x14" 1  
  Adhesive Magnetic Sheet - 14"x14" 1  
  Spring Steel Flexible Print Surface - 14"x14" 1  
  Keenovo Silicone AC Heater w/ thermistor - 300x300mm (650W) 1  
]]> DIY Projects Ray https://diycnc.ca/community/diy-projects/voron-2-4-parts-and-kit/